混凝土密封固化劑材料环境要求以及施工方法

滲透到混凝土裡面的化合物與已凝結的混凝土中所含的半水化水泥，遊離鈣，氧化矽等物質經過一系列復雜的化學反應，產生硬質性物質，這些化合物最終會使混凝土表層的密實度提高，從而提高混凝土表層的強度、硬度、耐磨性、抗滲性等指標，這類產品被稱為混凝土密封固化劑。
Compounds penetrated into concrete and semi-hydrated cement, free calcium, silica and other substances contained in the condensed concrete undergo a series of complex chemical reactions to produce hard substances. These compounds will eventually make the surface of concrete compactness increased, thereby improving the strength, hardness and resistance of the concrete surface. Such properties as grinding and impermeability are called concrete sealing agents.
混凝土密封硬化环氧地坪
Concrete seal hardened floor
復雜的化學反應最終產物會堵塞、固封混凝土的結構孔隙，強度的提高帶來表面硬度的提高，密實度的提高帶來抗滲性的提高。減少水份流動的路徑，即減少有害物質的侵入，從而大大增強瞭混凝土的抗化學物質的侵蝕能力。所以混凝土密封固化劑能帶來長久的密封、堅固、耐磨、無塵的混凝土表層。
The final product of complex chemical reaction will plug and seal the pore of concrete structure. The increase of strength will bring about the improvement of surface hardness, and the increase of density will bring about the improvement of impermeability. Reducing the path of moisture flow, that is, reducing the invasion of harmful substances, thus greatly enhancing the corrosion resistance of concrete to chemical substances. Therefore, concrete sealant solidifying agent can bring long-term sealing, strong, wear-resistant, dust-free concrete surface.
混凝土密封固化劑對环境的要求：
Environmental requirements for concrete sealing agents:
混凝土密封固化劑的施工要求裡對空氣相對濕度的要求是小於80%。因為混凝土密封固化劑是水性塗料，如果空氣濕度過大，混凝土含水量過高，混凝土密封固化劑將始終溶於水，而無法與混凝土內部的無機化合物和氧化鈣反應，從而更無法與生成物進行二次反應。
The requirement for air relative humidity in construction requirements for concrete sealing agents is less than 80%. Because the concrete sealant curing agent is water-borne coating, if the air humidity is too high, the concrete moisture content is too high, the concrete印花地坪 sealant curing agent will always be dissolved in water, and can not react with the inorganic compounds and calcium oxide in the concrete, so it can not react with the generated organisms.
混凝土密封硬化环氧地坪
Concrete seal hardened floor
混凝土密封固化劑施工方法：
Construction method of concrete seal curing agent:
1、將基層表面清理幹凈、除去浮灰，油污等不利於粘結的物質;若為舊基層坑窪過多需預先補平;依施工面積計量好高滲透密封固化劑用量。
1. Clean up the surface of the base course, remove the floating ash, oil dirt and other materials which are not conducive to bonding; if there are too many pits in the old base course, it is necessary to make up in advance; measure the amount of high permeability sealant curing agent according to the construction area.
2、將高滲透密封固化劑均勻倒在地面上，自由流動滲透，同時可用抹子輕刮使整個地面均勻滲透;當基面滲透反應變得滑稠，用水霧濕潤粘稠表面使高滲透密封固化劑繼續滲透反應。
2. Pour the high-permeability sealant evenly on the ground, and flow freely. At the same time, the whole ground can be penetrated evenly by a gentle scrape with a wiper. When the base surface penetration reaction becomes slippery and thick, the high-permeability sealant will continue to penetrate through the viscous surface wetted by water mist.
3、觀察基面的密實程度和滲透狀況，進行塗刷地面三遍及以上高滲透密封固化劑。
3. Observe the compactness and permeability of the base surface and brush the ground three times 透水地坪or more.
4、待基面滲透反應完全後(表面水分沒有完全幹燥為佳)，使用專業的清洗地面機器，去清洗表面以及除去多餘的材料。
4. After the base surface penetration reaction is complete (surface moisture is not completely dry is preferred), use professional ground cleaning machines to clean the surface and remove excess materials.
5、在完工24小時後，用軟毛拋光墊在地坪表面上拋光，需用樹脂磨片對基面進行多次拋光處理。使用時間越長，光澤度越好。
5. After 24 hours, use soft wool polishing pad to polish the surface of the floor, and use resin abrasive to polish the base surface several times. The longer it takes, the better the gloss.